PRODUCTS
| Product name | Application | Processing & Use level | Characteristics |
| K7567 | Functional leveling agent | □ Extrude after premixing<br> □ Dosage is 0.7-1.5% of total formula weight | ■ Prevent pits, pinholes, fish eyes, etc.<br> ■ Excellent leveling performance and weather resistance, good compatibility |
| K7572 | Functional leveling agent | □ Extrude after premixing<br> □ Dosage is 0.6-1.5% of total formula weigh | ■ Significantly improve the melt flow of the system<br> ■ Prevent pits, pinholes, fish eyes, etc.<br> ■ The coating film has excellent leveling and fullness |
| SA88 | Leveling agent | 0.8-1.2% of the formula | ? Applicable to various powder paint, the overall situation is good, easy to control ? Promoting flow flat, significant effect . ? Enhance the powder loosening, enhancing the rate of powder |
| K7573 | Leveling agent | 0.6-1.5% of the formula | ? Preventing defects such as pits, pinholes, and fisheyes; ? Excellent leveling performance and weather resistance; ? Good film appearance and recoatability. |
| Product name | Application | Processing & Use level | Characteristics |
| SA550 | Matting agent (GMA resin) | □ Incorporated into formula before extrusion<br> □ Epoxy value is about 700 | ■ The lowest gloss＜5%(60°)<br> ■ Excellent weather resistance and anti-yellowing |
| SA580 | GMA matting resin | □ Premix with binder before extrusion<br> □ Epoxy value approx 650 | ■ Gloss range 1-10%<br> ■ Fine and smooth levelling<br> ■ Excellent impact and bending resistance |
| SA300 | GMA resin | □ Incorporated into formula before extrusion<br> □ Epoxy equivalent value is about 300 | ■ Increase the cross link density <br> ■ Improve the mechanical strength and heat resistance,chemical resistance |
| Product name | Application | Processing & Use level | Characteristics |
| K7318 | Low temperature curing accelerator | □ Incorporated into formula before extrusion<br> □ 0.5-2% by weight of total formula | ■ Reduce curing temperature,shorten curing time<br> ■ Improve leveling and anti-yellowing<br> ■ Reduce the gloss fluctuations with curring temperature |
| SA316 | Curing accelerator | □ Incorporated into formula before extrusion<br> □0.05-0.5% by weight of total formula | ■ 100% active constituent<br> ■ Reduce curing temperature,shorten curing time |
| K7312 | Low temperature curing accelerator | □0.5-1% by weight of total formula | ? Significantly improve the solvent resistance and impact resistance of the coating film. ? Improve the gloss stability of polyester/GMA matting system. ? Does not affect leveling and clarity of the coating film. |
| Product name | Application | Processing & Use level | Characteristics |
| SA2165 | Matting agent for hybrid | □ Incorporated into formula before extrusion □1-5% by weight of total formula |
■ Provide 12-70%(60°) of gloss ■ Wide range of applicability to polyester resins ■ Good flow and anti-yellowing |
| SA2165D | Matting agent for hybrid | □ Incorporated into formula before extrusion □ 1-5% by weight of total formula |
■ Provide 8-60%(60°) of gloss ■ Good storage stability ■ Lower gloss with lower usage |
| K7227 | Matting agent for hybrid | □ Incorporated into formula before extrusion □ 1-4.5% by weight of total formula |
■ Provide 3-40%(60°)of gloss ■ Cost saveing ■ Improve mechanical property |
| K7232 | Matting agent for hybrid | □ Incorporated into formula before extrusion □ 1-5% by weight of total formula □ 1phw K7232 react with 2.5phw epoxy |
■ lowest gloss approx 3% ■ Good levelling ,storage stability improvement ■ Improving applicability to polyester resins |
| K7225 | Matting agent for hybrid | □ Incorporated into formula before extrusion □ 1-4.5% by weight of total formula |
■ Provide 6-60%(60°) of gloss ■ Excellent flow and anti-yellowing ■ Wide range of applicability to polyester resins Jietonda? K7225 |
| SA2065K | Physical Matting Agent for Hybrid System | □ Extruded after premixing, the dosage is 1-4.5% of total formula weight | ■ Provides 5-70% (60 °) gloss ■ Good leveling and storage stability ■ Low resin selectivity for wide range baking |
| K7237A | Physical Matting Agent for Hybrid System | □ Extruded after pre-mixing, the amount is 1-5% of the total weight of the formula. One part of K7233 requires 1.5 parts of E-12 epoxy | ■ Provides a minimum of about 2% (60 °) gloss<br> ■ Excellent storage performance<br> ■ Good leveling and strong resin adaptability |
| K7232D | matting hardener for hybrid | Incorporated into formula before extrusion 1-5% by weight of total formula 1phw K7232D react with 1.5phw epoxy | Excellent matting effect, the lowest gloss can reach 5% (60°) Excellent leveling performance and surface fineness; Excellent storage stability ; Environmental protection and low smoke. |
| Product name | Application | Processing & Use level | Characteristics |
| SA206A | Matting agent for PES/TGIC | □ Incorporated into formula before extrusion<br> □ 1-3% by weight of total formula | ■ Provide 30-70%(60°) of gloss<br> ■ Good weather resistance and low usage |
| K7216 | Matting agent for PES/TGIC | □ Incorporated into formula before extrusion □ 2-6% by weight of total formula |
■ Provide 10% (60°)of gloss ■ Good flow and excellent anti-yellowing ■ Low wax |
| SA2061B | Matting agent for PES/TGIC | □ Dry blend<br> □ 1-1.5% by weight of total formula | ■ Provide 10-40% (60°)of gloss<br> ■ Low usage and good gloss stability |
| SA2068 | Matting hardener for PES/TGIC | □ Incorporated into formula before extrusion □ 1-5% by weight of total formula |
■ Provide 10%(60°) of gloss ■ Good flow and good film hardness |
| K7217A | Matting agent for PES/TGIC | □ Incorporated into formula before extrusion<br> □ 1-5% by weight of total formula | ■ Provide 16%(60°) of gloss<br> ■ Excellent gloss stability and and anti-yellowing |
| K7212 | PES / TGIC system physical matting agent | □ Extruded after pre-mixing, the dosage is 2-6% of total formula weight | ■ Provides about 20-60% (60 °) gloss ■ Good gloss stability ■ Good leveling and anti-yellowing |
| K7215 | Matting agent for PES/TGIC | Extruded after pre-mixing, the dosage is 4-6% of total formula weight | ? Provide lowest 5% (60°) gloss ? Excellent leveling with good mechanical property . ? Good stability for baking, recommended to use in anti-yellowing condition. |
| Product name | Application | Processing & Use level | Characteristics |
| K7656 | Degassing agent for powder coatings | □ Premix with binder before extrusion □ 0.5-2% by weight of total formulation |
■ Reducing surface defects such as pits and pinholes ■ Without affecting coating gloss and screen printing ■ Non-yellowing,suitable for HAA system |
| SA500 | Slip and Degassing agent | □ Incorporated into formula before extrusion □ 0.5-1% by weight of total formula |
■ Improve the film appearance and anti-yellowing ■ Substitute of benzoin |
| SA501 | Film hardening agent | □ Incorporated into formula before extrusion □ 0.5-1% by weight of total formula |
■ Improve the hardness and smoothness of film |
| SA5060 | Anti foaming agent | □ Incorporated into formula before extrusion □ or dry blend □ 0.5-1.5% by weight of total formula |
■ Eliminate pinholes,bubbles and craters ■ Used on porous substrates,such as cast iron ■ cast aluminum alloys |
| SA5066 | Special film hardening agent | □ Incorporated into formula before extrusion □ or dry blend □ 0.5-1.5% by weight of total formula |
■ Increasing hardness, scratch/friction resistance |
| K7661 | Degassing agent for powder coatings | □ Premix with binder before extrusion or dry belend □ 0.5-1.5% by weight of total formulation |
■ High degassing efficiency ■ Recommended for porous substrates |
| Product name | Application | Processing & Use level | Characteristics |
| K7101 | Epoxy hardener/curing accelerator | □ Incorporated into formula before extrusion □ As curing agent,e the use level is 2-4phr on epoxy resin |
■ Excellent flow and low usage ■ Used as curing agent, curing @120℃/30min ■ Used as accelerator, curing @240℃/30s |
| K7104 | Epoxy hardener | □ Incorporated into formula before extrusion □ As sole curative the use level is 3-5phr on epoxy resin |
■ Curing @ 140℃/15min or 240℃/30s ■ Applied for thick film coatings or FBE coatings ■ Good mechanical properties ■ Good chemical resistance |
| K7108 | Epoxy hardener | □ Incorporated into formula before extrusion □ As sole curative the use level is 4-6phr on epoxy resin |
■ Curing @ 150℃/10min or 240℃/2min ■ Applied for thin film decorative coatings or functional epoxy powder coatings ■ Good film appearance and mechanical strength |
| SA31 | Epoxy hardener/curing accelerator | □ Incorporated into formula before extrusion □ As accelerator, use level is 0.1-0.5% on total formula |
■ For functional or decorative powder coatings ■ Curing @ 140℃/30min |
| SA2830 | Epoxy hardener | □ Incorporated into formula before extrusion □ 3.5-4.5phr on epoxy resin |
■ For functional or decorative powder coatings ■ Curing @ 180℃/15min |
| SA2831 | Epoxy hardener (accelerated DICY) | □ Incorporated into formula before extrusion □ 4-5phr on epoxy resin |
■ For functional or decorative powder coatings ■ Curing @ 160℃/12min or 200℃/5min |
| SA3120 | β-HAA hardener | □ Incorporated into formula before extrusion □ Hydroxyl equivalent value is about 84 |
■ Eco-friendly,Low-toxicity,anti-yellowing ■ Exterior application, Substitute of TGIC |
| K7150 | Blocked polyisocyanate curing agent for PU powder coatings | It is recommended to cure with hydroxyl polymer in equivalent amount (13:87 for polyester with hydroxyl value of 30; 20:80 for polyester with hydroxyl value of 50) | ? Extremely high crosslink density , excellent surface hardness and chemical resistance for coating . ? Excellent leveling and smoothness. ? Excellent weather resistance. |
| K7152 | Blocked polyisocyanate curing agent for powder coatings | It is recommended to cure with hydroxyl polymer in equivalent amount 13:87 for polyester with hydroxyl value of 30; 20:80 for polyester with hydroxyl value of 50 | ? Extremely high crosslink density , excellent surface hardness and chemical resistance for coating . ? Excellent leveling and smoothness. ? Excellent weather resistance and anti yellowing performance. |
| Product name | Application | Processing & Use level | Characteristics |
| SA207 | Texture additive | □ Incorporated into formula before extrusion □ 0.08-0.15% by weight of total formula |
■ low usage ■ Impart sand grain finishes ■ Use for electrical appliances and IT equipments |
| SA2072 | texture additive | □ Incorporated into formula before extrusion □ 0.1-0.2% by weight of total formula |
■ low cost ■ Impart sand grain finishes ■ For almost all kinds of powder coatings |
| SA208 | Special texture additive | □ Incorporated into formula before extrusion □ 3.5-5% by weight of resin |
■ For almost all kinds of powder coatings ■ Impart special texture finishes such as wrinkle, reticulated, vein, embossed and grained |
| K7726 | texture additive | □ Incorporated into formula before extrusion □ 0.2-0.6% by weight of total formula | ● It can form a sand-like coating with excellent wear resistance. ● The sand texture surface is smoother and more delicate. ● Suitable for powder coatings of any system, such as pure epoxy, epoxy/polyester, polyester/TGIC or HAA and PU. |
| Product name | Application | Processing & Use level | Characteristics |
| SA2483 | Charge enhancing agent | □ Incorporated into formula before extrusion □ 0.3-0.6% by weight of total formula |
■ Enhance the conductivity ■ Improve the film appearance ■ Anti yellowing |
| SA2485 | Charge enhancing agent | □ Incorporated into formula before extrusion □ 0.2-0.5% by weight of total formula |
■ Excellent conductivity performance ■ Improve the film appearance and flow ■ Better overall performance than SA2483 |
| SA2486 | Charge enhancing agent | □ Incorporated into formula before extrusion □ 0.2-0.4% by weight of total formula |
■ Excellent conductivity performance ■ Use for both corona gun and tribo gun |
| SA2487 | Charge enhancing agent | □ Incorporated into formula before extrusion □ 0.3-1.5% by weight of total formula | ■ No catalytic activity, does not affect the gloss of the coating and the gel time of the coating. ■ Good geothermal stability and anti-yellowing properties. ■ Does not affect powder storage stability. |
| K7017 | Charge enhancing agent | □ Incorporated into formula before extrusion □ 0.3-1.5% by weight of total formula | ■ No catalytic activity ,so no negative effect to the gloss of coating and gel time . ■ Good thermal stability and anti-yellowing properties. |
| Product name | Application | Processing & Use level | Characteristics |
| SA516 | Pigment dispersant | □ Incorporated into formula before extrusion □ 0.5-1% by weight of total formula |
■ Good pigment dispersing ability ■ Provide better color strength |
| K7005 | Anti-yellowing agent | □ Extruded after premixing, the dosage is 0.3-1% of the total weight of the formula | ■ For a variety of powder coating systems, especially HAA systems ■ Can significantly inhibit the yellowing of powder coatings caused by gas baking or electric baking |
| K7301A | Bonding additive | Refer to the TDS | ■ Improve the metal effect of coatings ■ Increase bonding temperature and anti caking ■ Reduce the dosage of metal pigments |
| SA5501 | Stabilizer for metal pigment | □ Dry blend □ 2-3% by weight of total formula |
■ Inhibiting from blackening, spot-formation and loss of brilliance of metallic coatings ■ Improve heat resistance |
| SA5502 | Dry powder flow additive | □ Dry blend □ 0.1-0.5% by weight of total formula |
■ Improving fluidity of coating powders ■ Anti caking ■ Enhancing electrostatic spray efficiency ■ Controlling film thickness for thin coating |
| K7921 | Adhesive modifier | Extruded after premixing, the dosage is 0.8-1.5% of the total weight of the formula | Improve the adhesion of the coating to metal substrates such as stainless steel and galvanized sheet, improve the flexibility of the coating without affecting the weatherability |
| K7010A | Special anti-caking additive | □ Dry blend □ 0.2-0.4% by weight of total formula | ■ Anti caking ■ For almost all kinds of powder coatings ■ Improving fluidity of coating powders |
| K7658 | surface wetting modifier | □ Incorporated into formula before extrusion □ 0.5-2% by weight of total formula | ? Good pigment and filler wetting and dispersing properties and allow to increase the amount of pigment and filler. ? Good wetting performance, improve the coating fog, improve the clarity and freshness of the coating. |
| K7771 | wear-resistant agent | □ Incorporated into formula before extrusion □ 0.2-0.5% by weight of total formula | ? Can form a coating with excellent wear resistance. ? Especially suitable for sand texture formula. |
| K7004 | Anti-yellowing agent | □ Extruded after premixing, the dosage is 0.5-1.5% of the total weight of the formula | ? Significantly improving discoloration and performance deterioration because of gas baking ; ? Can be used in PES/TGIC and PES/H AA systems, etc. |
| K7007 | Anti-yellowing agent | □ Extruded after premixing, the dosage is 0.2-1% of the total weight of the formula | ? Can significantly inhibit yellowing of powder coating caused by electric baking and gas baking. ? Can significantly inhibit the aging of the powder coating caused by high temperature baking, can withstand high temperature baking at 220-250 ℃. |
| K7010B | Anti caking agent | □ Dry blend □ 0.1-0.4% by weight of total formula | ? Significantly improve the dry powder fluidity and construction ? No harm to the leveling and mechanical properties of the coating. |
| K7923 | Adhesion promoter | Extruded after premixing, the dosage is 0.5-1.5% of the total weight of the formula | ? Significantly improve the adhesion of the coating to special metal substrates such as galvanized, magnesium aluminum alloy; |
PRODUCTS
HOTLINE:
+86-564-3711165
+86-13966241417
Mobile version
Search
| Add: 15 Li Dun, North Outskirts of Luan City, Anhui, P, R, China P.C.:237158 | |
| Tel: +86-564-3711165 , +86-564-3711777 | |
| Fax: +86-564-3711167 | E-mail: jietonda@jietondachem.com |
Copyright(C)2019, Lu'An Jietonda New Material Co.,Ltd. All Rights Reserved. Supported by ChinaChemNet ChemNet Toocle Copyright Notice 備案序號：皖I(lǐng)CP備11004581號